stop device



Stopping device 1. Electrical contact stop device (1) Type: Electrical contact type. (2) Warp stop piece: electrical contact type warp stop piece. (3) Number of stops: 2 to 8. (4) …

Stopping device

1. Electrical contact stop device
(1) Type: Electrical contact type.
(2) Warp stop piece: electrical contact type warp stop piece.
(3) Number of stops: 2 to 8.
(4) Rated working voltage: 12VDC or 24VDC.
(5) Applicable box width: 1250~4600mm.
2. Specifications, models and adapted models
(1) Number of columns: 2 columns, 4 columns, 6 columns, 8 columns.
(2) Effective width: 1250, 1300, 1600, 1800, 1900, 2000, 2100, 2200, 2300, 2400, 2500, 2600, 2800,
3000, 3200, 3300, 3600, 4200, 4600, The units are all mm.
(3) Applicable models: various types of rapier looms, air-jet looms, water-jet looms and projectile looms.
3. Requirements for the warp stop strip
(1) The warp stop strip must have certain physical and mechanical properties and shape, the surface should be straight, and its cross-section should be similar to the groove of the warp stop piece.
(2) The warp stop strip must have a certain stiffness to avoid excessive deformation and bending after hanging the warp stop strip.
(3) The surface of the warp stop bar should have a certain hardness, strong wear resistance, smooth surface, coating, corrosion resistance and rust prevention.
(4) The stop bar used for electrical automatic stop devices should have good electrical conductivity to ensure sensitive stop.
4. Use and maintenance of the stop strip
(1) The stop strip cannot be bent rigidly, and you need to be very careful when moving it after putting on the stop strip to avoid damaging the stop strip.
(2) When inserting the warp stop strip into the warp stop piece, you need to first check whether its insulation performance is good. After putting on the warp stop piece, when installing it back to the warp stop frame
It is necessary to strictly check the accuracy of the installation position and the The reliability of electrical connections prevents malfunctions.
(3) The stop strips must not get wet and need to be sealed in a dry environment for long-term storage.
(4) If the use environment of the stop strip has high humidity, it must be dried regularly.
(5) After long-term friction between the warp stop bar and the warp stop piece, grooves will appear on the outer shell of the warp stop bar, and the long hole in the warp stop piece will become wider, which will change the contact between the warp stop bar and the warp stop piece. distance, which may cause the loom to malfunction, and the warp stop bar or warp stop piece needs to be replaced in time depending on the situation.
(6) The stopped insulation layer will age after long-term use, affecting the insulation performance. Long-term use in a high-humidity environment will also affect the insulation performance, and then the machine will not be able to be turned on. The indicator light indicates a broken warp. At this time, the warp stop strips need to be dried or replaced in time.
5. Manufacturers of stop plates and stop devices
AAANGMKJLOI87

Extendedreading:https://www.alltextile.cn/product/product-61-527.html
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
Extendedreading:
ExtendedReading:
Extendedreading:
Extendedread

This article is from the Internet, does not represent 【www.chinagarments.com】 position, reproduced please specify the source.https://www.chinagarments.com/archives/10379

Author: clsrich

 
TOP
Home
News
Product
Application
Search